Withdrawal Sleeves

Withdrawal Sleeves

Features:
Withdrawal sleeves can be used to mount bearings with a tapered bore on cylindrical seats of stepped shafts. The sleeve is pressed into the bore of the bearing that abuts a shaft shoulder or similar fixed component. The sleeve is located on the shaft by a nut or an end plate. Lock nuts or end plates are not supplied with the extraction sleeves. KM or HM lock nuts and respective locking washers are suitable but must be ordered separately. Further information will be found in the section “Lock nuts with locking washer or clip”. To secure the bearing to the shaft, press the extraction sleeve into the bearing bore. To do this, particularly where larger bearings are concerned, considerable force is required to overcome the friction between the mating surfaces of the bearing and sleeve and of the sleeve and shaft. Mounting and dismounting of bearings on extraction sleeves can be facilitated considerably by using a hydraulic nut.

Withdrawal sleeves are used for mounting tapered bearings on to the cylindrical shafts. They facilitate easy mounting, securing and dismounting. They are suitable for both smooth and stepped shafts. Bearing sleeve can easily adapt to the shaft diameter. They are usually coated with a preservative, are slotted and have an external taper. This allows the sleeve to be used with wide spherical roller bearings. Withdrawal sleeves for oil injection have oil ducts and distribution grooves, on the threaded side.

Product Features:
1) Allows maintenance-free and long-life operation
2) Suitable for high static and dynamic loads
3) Low and smoothly coefficient of friction and without stick-slip effects
4) Suitable for dirty,corrosion,impact load and edge loading
5) Base material provided a good shock-absorbing capacity
6) Can be used over large temperature range
7) Suitable for reciprocating, rotating and oscillating movement with start frequency and difficulty to form oil film occasions
8) With low wear rate and long life service
9) Allows maintenance-free and long-life operation

Parameter:
Hot sale types of Withdrawal sleeves

Withdrawal Dimension (mm) Mass Lock nut
Sleeve d1 d B3 B4 D1 D2 a b f G (kg) No.
AH2308 35 40 40 43 42.76 42 10 7 2 M45x1.5 0.128 KM09
AH2309 40 45 44 47 48.08 47.5 10 7 2 M50x1.5 0.164 KM10
AH2310 45 50 50 53 53.5 52 12 9 2 M55x2 0.209 KM11
AH2311 50 55 54 57 58.67 57 13 10 3 M60x2 0.253 KM12
AH2312 55 60 58 61 63.92 62 14 11 3 M65x2 0.297 KM13
AH2313 60 65 61 64 69.08 68.5 15 12 3 M75x2 0.395 KM15
AH2314 65 75 64 68 74.42 73.5 15 12 3 M80x2 0.466 KM16
AH2315 70 80 68 72 79.75 79 15 12 3 M85x2 0.534 KM17
AH2316 75 85 71 75 85 84.5 15 12 3 M90x2 0.597 KM18
AH2317 80 90 74 78 90.17 89.5 16 13 3 M95x2 0.69 KM19
AH2318 85 95 79 83 95.5 95 17 14 3 M100x2 0.779 KM20
AH2319 90 100 85 89 100.83 100 19 16 4 M105x2 0.886 KM21
AH2320 95 105 90 94 106.25 105.5 19 16 4 M110x2 0.998 KM22
AH2322 105 110 98 102 116.92 116 19 16 4 M125x2 1.35 KM25
AH2324 115 120 105 109 127.42 126.5 20 17 4 M135x2 1.6 KM27
AH2326 125 130 115 119 138.08 137.5 22 19 4 M145x2 1.97 KM29
AH2328 135 140 125 130 148.92 148 23 20 4 M155x3 2.33 KM31
AH2330 145 150 135 140 159.42 158.5 27 24 4 M165x3 2.82 KM33
AH2332 150 160 140 146 169.92 168 27 24 5 M180x3 4.72 KM36
AH2334 160 170 146 152 180.42 179 27 24 5 M190x3 5.25 KM38
AH2336 170 180 154 160 189.92 189 29 26 5 M200x3 5.83 KM40
AH2338 180 190 160 167 201.25 200 32 26 5 T210x4 6.63 KM42
AH2340 190 200 170 177 211.75 210 36 30 5 T220x4 7.54 KM44
AH2344 200 220 181 189 232.75 231 36 30 5 T240x4 13.5 KM48
AH2348 220 240 189 197 253.42 252 36 30 5 T260x4 15.5 KM52
AH2352 240 260 205 213 274.75 273 36 30 6 T290x4 19.6 KM58
AH2356 260 280 212 220 295.33 294 36 30 6 T310x5 21.6 KM62